Commit 5579e73c authored by Derald D. Woods's avatar Derald D. Woods Committed by Tom Rini

ARM: dts: omap3-evm: Sync dts(i) files from Linux 5.1.5

Signed-off-by: default avatarDerald D. Woods <woods.technical@gmail.com>
parent 8dd6803d
......@@ -90,19 +90,19 @@
label = "X-Loader";
reg = <0 0x80000>;
};
partition@0x80000 {
partition@80000 {
label = "U-Boot";
reg = <0x80000 0x1c0000>;
};
partition@0x1c0000 {
partition@1c0000 {
label = "Environment";
reg = <0x240000 0x40000>;
};
partition@0x280000 {
partition@280000 {
label = "Kernel";
reg = <0x280000 0x500000>;
};
partition@0x780000 {
partition@780000 {
label = "Filesystem";
reg = <0x780000 0x1f880000>;
};
......
......@@ -122,6 +122,7 @@
};
&mmc2 {
interrupts-extended = <&intc 86 &omap3_pmx_core 0x12e>;
vmmc-supply = <&wl12xx_vmmc>;
non-removable;
bus-width = <4>;
......@@ -132,8 +133,10 @@
wlcore: wlcore@2 {
compatible = "ti,wl1271";
reg = <2>;
interrupt-parent = <&gpio5>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 149 */
/* gpio_149 with uart1_rts pad as wakeirq */
interrupts-extended = <&gpio5 21 IRQ_TYPE_EDGE_RISING>,
<&omap3_pmx_core 0x14e>;
interrupt-names = "irq", "wakeup";
ref-clock-frequency = <38400000>;
};
};
......
......@@ -86,6 +86,10 @@
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
>;
};
......@@ -127,9 +131,13 @@
>;
};
/*
* Note that gpio_150 pulled high with internal pull to prevent wlcore
* reset on return from off mode in idle.
*/
wl12xx_gpio: pinmux_wl12xx_gpio {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_cts.gpio_150 */
OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
>;
};
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment